So the goal was to modify this Steadicam Smoothee for lightweight cameras, but it was surprising to see it fly my Canon 5D Mark II + 50mm F/1.4 Lens. Getting back to the real reason for the mod, I tested out a smaller setup with the GH2 + 20mm Lens (total 1.2lbs). It took about 6.8oz of counterweight, but she balances just fine. In fact, I really think Tiffen should offer something like this for all the new smaller lightweight cameras coming out. If they can keep the price about the same, they'd make quite an impact. There's some additional information in the video about the Quick Release mount and Counterweight attachment.
Yup, within the first few minutes the Steadicam Smoothee walked through the door it was laying helplessly in pieces on my workbench. As I suspected, it's quite easy to modify this little stabilizer. With a quick release adapter, a top stage that can be fine tuned Left/Right & Forward/Back for easy balance, and one of the smoothest Gimbals on the market, i'm calling this the 'Cheesycam Baby Merlin'. If you haven't seen how smooth the Gimbal is, check out the earlier video (here).
The original Steadicam Merlin will run you about $800 dollars (click here to see), and I know there's a ton of people who want something similar for their GH2 or Sony NEX5n cameras. With this DIY, you can have just about the same features for 1/5th the price! Here's how I went about the mod.
Peel Back the sticker at the base and you'll find a few small screws. Remove the metal plates inside so you can drill through the base.
I reassembled the base (without the metal plates) and then drilled through the center (almost center - oops). Using a 3/8" Drill Bit, I was able to stuff a 1/4 x 20 coupler perfectly inside.
On the underside of the coupler, I added a washer and 1/4x20 screw to keep it from pulling through the top. On top I added my weight bracket. You could use just about anything here, and my counterweight was at 13.6 oz. which is needed to counter balance the 5D Mark II + 50mm F/1.4 (2.6lbs total).
DIY TIP
If you want to build your own counterbalance that can swing left to right, and allow you to adjust weights up or down, check out this little mock-up using basic off the shelf parts (below). An Eye Bolt will be at the top of your counterweight setup (attached to the base of the Smoothee). A threaded coupler will allow you to attach a long all-thread rod. You can use heavy washers on the rod and a pass-through thumb knob at the bottom. You'll probably need a second thumb knob above the washers to clamp them down. If you need to make it less bottom heavy adjust the weights upwards. If you need to make it more bottom heavy, adjust the weights downwards.
Click image for larger view
Or you could also start with one of these slotted metal Dual Camera brackets to build up your swinging counterweight system. Dual Metal Camera Bracket
Not really a cost saving idea, but If you really wanted that finished look like mine has, then here's where I cannablized the lower counterweight bracket from. Opteka Video Camera Stabilizer
For the Quick Release plate, I used a hacksaw to cut straight across and filed it down flat.
Drilled a hole down the middle of the QR plate, and added a screw underneath. I had to trim a bit underside to get the screw to fit.
There you go! A modified Steadicam Smoothee made into the Cheesycam Baby Merlin. A nice stabilizer with an adjustable top stage, a Quick release mount, Fine Tuning knobs for quick balance, and adjustable weights underneath with movement to counterbalance uneven weight.
Originally modified to use with my Sony HX9V or Canon S100, but sturdy enough to rock my Canon 5D Mark II + 50mm F/1.4 (2.6lbs.) This is a no-brainer awesome Stabilizer for all kinds of smaller cameras like the Micro Four Thirds, or Sony NEX5n / NEX-7 type cameras. Right now these little Smoothee stabilizers are on sale (click here).
I want to say when these things were first released they were over $200 dollars. Ridiculous pricing if all you plan to fly is a cell phone. They have since dropped down in price, and while they are listed at about $180 dollars elsewhere, this month they're on sale at B&H (click here). Not bad if you could possibly do much more with it.
[Update] here's the video
With one of the smoothest Gimbals on any stabilizer ever, I decided to pick one up and see if it can be pushed to carry much more than a small GoPro. So far the Gimbal is made with a metal bearing, and the frame is mostly a lightweight metal. If it's possible to modify the frame to add more weights, then you're looking at an ultra smooth Gimbal on a Merlin-like stabilizer for almost 5 times cheaper than the Merlin itself.
There's a million different little stabilizers on the market, but about a month ago (maybe a bit longer), the Steady Dragon brand upgraded the Gimbal to a universal joint. This type of gimbal provides the maximum amount of range compared to the little Ball-and-Socket type like found in the Hague MMC. The Steady Dragon seems to have all the right parts with front and rear counterweights, side to side weights, and adjustment of the camera forward and back.
With the optional camera plate, you can also add side to side from the top stage. A Tripod mount is also available so you can dock your camera. There's ways to create your own stabilizer with U-Joint from a Traxxas RC, but If you're not the DIY type, this little stabilizer looks like a good start for small cameras and under a hundred bucks. The Steady Dragon states it's rated to balance cameras just around 3 lbs and you can find some demo videos following the link (click here).
The Skyler MiniCam has been a work in progress floating around the Internet for a very long time, but this is the first time i've seen it available on eBay. A clever little stabilizer which stands on it's own like a tripod, looks to have great build quality, and very simple fine tuning knobs. A 1/4-20 thread under the stabilizer allows you to mount it on a Monopod so that you can don't need to dismount your camera.
Unfortunately the asking price of over $620 dollars is a big umm..'heck no' for me. It's too bad they couldn't get the Skyler under the $200 dollar price tag, I think it could be a hit. I guess if you want to compare the price to an $800 dollar Steadicam Merlin, it's not looking so bad, but there's so many more stabilizer options now for under $300 dollars. If you're still curious, there's some additional demo videos of the Skyler MiniCam stabilizer in use over at the auction page (click here).
Skyler Mini DSLR Video Camera Stabilizer Steadicam
Today Tiffen announced at CES a newly designed Steadicam Merlin 2. One interesting additions is an upgrade to the handle that includes a remote to start / stop video. Not available in retail stores yet, but a full FAQ section and PDF user manual is available on the Tiffen website https://www.tiffen.com/steadicam_merlin2.html
Preparing for a last minute shoot today, I found my Steadicam Merlin Vest had cracked on the upper chest piece. Crap. The quick fix for me today was to use the top portion of the Konova Vest and mate it with the Steadicam Merlin Arm (which is held on with the waist area). There was a bit of hackery, drilling, and modding, but it managed to all come together in the end. The reason I needed to stick with the Steadicam ISO Arm is because the rig I had already built up was fairly lightweight. The Konova requires a good payload to be effective, but the Steadicam arm can be dialed to fly lighter sleds. So for today's shoot i'm Frankenstein-ed out with a vest that consists of a Konova Chest Piece, Steadicam Arm, and Glidecam sled...
Another Hollywood Ultralight turns up on auction. This ultralight stabilizer is a discontinued product, but works like a mini Glidecam (as seen in the video demonstration above). It can support cameras of up to 4lbs, but with all the new GF3 like cameras with HD video, it's too bad they don't start making these things again. eBay auction found (click here)
(Above) Video was just for fun, don't take it seriously
I've probably tested more stabilizers than the Brady Bunch Family has fingers and toes (combined). Not everything makes it on the blog, because it just ends up as wasted sapce. Now i'm not saying some of these stabilizers 'won't fly'. What I look into and weigh in on is Stabilizer vs. Price. With enough muddling around (a few days and a few modifications), you can probably get some decent shots with most stabilizers.
Since I just posted about questions on other Random stabilizers I don't think is worth the asking price, here's another one for you - not to consider. Besides looking quite odd, the current asking price is several times that of other stabilizers which are easier to fly and faster to balance. The handle has shock absorption, the stage can be positioned forward/back, and the weight can be shifted left/right. The odd color choice and design might have been based on old Buck Rogers technology. You would think the tripod stand base design would work well to sit your camera down, but it acts as a counterweight. If you are required to shift that weight to an angle, it will no longer sit as a tripod and just topple over.
The video demo was shot just for fun, and it was the first time out with it. It's definitely not easy to fly. I don't agree on the price tag running several hundreds of dollars while there are already existing units on the market that are much cheaper and already have proven results. If they dropped this down to about $80 dollars, it might be worth considering for those on a budget and a lack of aesthetic appeal. There is also a low mode version, and a kit that doubles as both low mode and tripod base mode found on eBay (click here).
Dual Metal Camera Bracket
